How to restart GitLab
Depending on how you installed GitLab, there are different methods to restart its service(s).
If you want the TL;DR versions, jump to:
- Omnibus GitLab restart
- Omnibus GitLab reconfigure
- Source installation restart
- Helm chart installation restart
If you have used the Omnibus packages to install GitLab, then
you should already have
gitlab-ctl in your
gitlab-ctl interacts with the Omnibus packages and can be used to restart the
GitLab Rails application (Unicorn) as well as the other components, like:
- GitLab Workhorse
- PostgreSQL (if you are using the bundled one)
- NGINX (if you are using the bundled one)
- Redis (if you are using the bundled one)
Omnibus GitLab restart
There may be times in the documentation where you will be asked to restart GitLab. In that case, you need to run the following command:
sudo gitlab-ctl restart
The output should be similar to this:
ok: run: gitlab-workhorse: (pid 11291) 1s ok: run: logrotate: (pid 11299) 0s ok: run: mailroom: (pid 11306) 0s ok: run: nginx: (pid 11309) 0s ok: run: postgresql: (pid 11316) 1s ok: run: redis: (pid 11325) 0s ok: run: sidekiq: (pid 11331) 1s ok: run: unicorn: (pid 11338) 0s
To restart a component separately, you can append its service name to the
restart command. For example, to restart only NGINX you would run:
sudo gitlab-ctl restart nginx
To check the status of GitLab services, run:
sudo gitlab-ctl status
Notice that all services say
Sometimes, components time out (look for
timeout in the logs) during the
restart and sometimes they get stuck.
In that case, you can use
gitlab-ctl kill <service> to send the
signal to the service, for example
sidekiq. After that, a restart should
As a last resort, you can try to reconfigure GitLab instead.
Omnibus GitLab reconfigure
There may be times in the documentation where you will be asked to reconfigure GitLab. Remember that this method applies only for the Omnibus packages.
Reconfigure Omnibus GitLab with:
sudo gitlab-ctl reconfigure
Reconfiguring GitLab should occur in the event that something in its
/etc/gitlab/gitlab.rb) has changed.
When you run this command, Chef, the underlying configuration management application that powers Omnibus GitLab, will make sure that all directories, permissions, services, etc., are in place and in the same shape that they were initially shipped.
It will also restart GitLab components where needed, if any of their configuration files have changed.
If you manually edit any files in
/var/opt/gitlab that are managed by Chef,
running reconfigure will revert the changes AND restart the services that
depend on those files.
Installations from source
If you have followed the official installation guide to install GitLab from source, run the following command to restart GitLab:
sudo service gitlab restart
The output should be similar to this:
Shutting down GitLab Unicorn Shutting down GitLab Sidekiq Shutting down GitLab Workhorse Shutting down GitLab MailRoom ... GitLab is not running. Starting GitLab Unicorn Starting GitLab Sidekiq Starting GitLab Workhorse Starting GitLab MailRoom ... The GitLab Unicorn web server with pid 28059 is running. The GitLab Sidekiq job dispatcher with pid 28176 is running. The GitLab Workhorse with pid 28122 is running. The GitLab MailRoom email processor with pid 28114 is running. GitLab and all its components are up and running.
This should restart Unicorn, Sidekiq, GitLab Workhorse and Mailroom
(if enabled). The init service file that does all the magic can be found on
your server in
If you are using other init systems, like systemd, you can check the GitLab Recipes repository for some unofficial services. These are not officially supported so use them at your own risk.
Helm chart installations
There is no single command to restart the entire GitLab application installed via
the cloud native Helm Chart. Usually, it should be
enough to restart a specific component separately (
gitlab-shell, etc.) by deleting all the pods related to it:
kubectl delete pods -l release=<helm release name>,app=<component name>
The release name can be obtained from the output of the
helm list command.